|
|
Post by Richard WR7FT on Dec 30, 2023 15:38:40 GMT
 I am currently running JTX 2.2.159win64 on an IC-7300 and Windows 11. Everything was working fine and then the program stopped producing audio and therefore no power out. Receive (microphone) and CAT work properly. I am using the same configuration on WSJT-X and it functions properly. I have downloaded the current libhamlib-4.dll and replaced the one in the directory. I have also checked the speaker setting and they seem to be properly set. Attached is a photo of the JTDX screen and IC-7300 showing no ALC and power out. Any ideas? |
|
|
|
Post by carloik2rpe on Dec 30, 2023 16:25:27 GMT
I cannot see the photo, but sometime I had the same problem: stupidly I didn't realize that the power rule at the right was at zero....
|
|
|
|
Post by Rafael EA3BIL on Jan 1, 2024 15:20:59 GMT
This is exactly what shows the image. Power slider on the right is ON THE LOWEST possible setting, so... No audio is coming out (or it's so, so, so, so low to produce TX) NOTE: I think you made a little mistake on the SUBJECT as version 2.2.259 has NOT yet been reached. NOTE2: (carloik2rpe): You need to be LOGGED IN to see the image...  |
|
|
|
Post by Richard WR7FT on Jan 8, 2024 22:09:39 GMT
I did check and the Pwr slider was on the lowest setting. I moved it to the 0db and did get power out thanks. Your right version 2.2.159-32A
Now the issue is that the message will start to send the ALC will move to zero and the Ip on the finals will move to 20A with maybe 10 watts out when the RF Power is set to 100%. I seems that the audio output is changing even though the slider for the IC-7300 speakers stays the same at about 40 to 50.
|
|
|
|
Post by w9mdb on Jan 8, 2024 22:17:41 GMT
Are you on a Dell computer?
If so go into Services and disable all "WAV" services.
Dell bloatware...
|
|
|
|
Post by Richard WR7FT on Jan 9, 2024 4:13:19 GMT
I'm using a HP Laptop. I didn't find any WAV services on the HP. Interesting, everything was working as normal and then the ALC started to vary on transmit.
|
|
|
|
Post by Rafael EA3BIL on Jan 9, 2024 7:42:39 GMT
I did check and the Pwr slider was on the lowest setting. I moved it to the 0db and did get power out thanks. Your right version 2.2.159-32A Now the issue is that the message will start to send the ALC will move to zero and the Ip on the finals will move to 20A with maybe 10 watts out when the RF Power is set to 100%. I seems that the audio output is changing even though the slider for the IC-7300 speakers stays the same at about 40 to 50. BTW, If you slide it up, pay attention to ALC. I always try to keep it below 20% and also noticed this set needs to be raised a bit on high TX tones. (Maybe 'cause of my external sound card). |
|
|
|
Post by Richard WR7FT on Jan 12, 2024 17:04:26 GMT
IC-7300 JTDX TX Issue slide show 3.mp4 (868.46 KB) Attached is a slide show (video is too large) of the audio changing during an FT8 Transmission. It starts out fine, then the audio drops out (ALC goes to 0 and Ip increases with lower RF power out) then picks up again. Here is the link to the entire video. youtu.be/vOomqO0xcVc
|
|
I am currently running JTX 2.2.159win64 on an IC-7300 and Windows 11. Everything was working fine and then the program stopped producing audio and therefore no power out. Receive (microphone) and CAT work properly. I am using the same configuration on WSJT-X and it functions properly. I have downloaded the current libhamlib-4.dll and replaced the one in the directory. I have also checked the speaker setting and they seem to be properly set. Attached is a photo of the JTDX screen and IC-7300 showing no ALC and power out. Any ideas? 
